ConMed Hyfrecator 2000 Electrosurgical Unit

The Hyfrecator® has been the #1 product of choice by physicians in office based electrosurgery for over 60 years. CONMED is pleased to continue this tradition with the new Hyfrecator®2000 which features: Memory to store up to 3 power settings. Remote control handpiece to change power settings, maintain the sterile field and decrease procedural time. Dual Microprocessors: one to control the function and output of the Hyfrecator®, the second to terminate activation if a hazard or safety issue isdetected. Cost effective alternative to various laser procedures.

Included with purchase:

• Power up/down switching handle and cord (7-800-5)
• Wall mount kit (7-796-20)
• Two Non-sterile sheaths (7-796-18)
• Two Sterile sheaths (7-796-19)
• Box of50 Disposable Electrolase® Blunt tips (7-101-12)
• Box of50 Disposable Electrolase®Sharp tips (7-100-12)
• Procedural video (7-900-12)
• Operator's manual and warranty card (7-900-OM)

Remote control on handpiece:

Save procedural time and ensures sterility when operating in a sterile field

High or Low Output ports:

Conveniently switch back and forth between settings depending on your procedure. Save your most common procedural settings in both high and low mode. Precise output at low and high settings

Dual Microprocessors:

One microprocessor controls the output and functionality of the system while the second terminates activation if a safety hazard is detected. This makes the Hyfrecator 2000 one of the safest office-based electrosurgery units in the world.

Self-diagnostic test at power up:

Self-diagnostic tests are performed every time you turn on the Hyfrecator 2000. This ensures that all systems are functioning properly which increases patient safety.

Memory to save power settings:

Computer memory saves the last procedural setting until you change it yourself. Automatically saves high, low and bipolar settings.

• Memory to store up to 3 power settings.
• Remote control handpiece to change power settings, maintain the sterile field and decrease procedural time.
• Dual Microprocessors: one to control the function and output of the Hyfrecator®, the second to terminate activation if a hazard or safety issue is detected.
• Cost effective alternative to various laser procedures.

Primary Power Requirements

• Model 7-900-115 115V± 10% 50/60 Hz 0.8 A

Dimension and Weight

• Depth: 4 inches (102 mm)
• Width: 8.75 inches (222 mm)
• Height: 7.5 inches (190 mm)
• Weight: 6 pounds (2.7 kg)

Power Accuracy at Rated Load

LO and BI:

• 0 to 10 W: Greater of 90 mW or 10% of setting
• 10 to maximum setting: 10% of setting

HI:

• Greater of 1 W or 10% of setting

NOTE: Instrumentation errors can be great enough to exceed these limits. For best results, the same instruments should be used for calibration, as well as checking.

RF Frequency: 450 KHz ±50KHz (open circuit)

Output Wave Shape: Clipped, damped sinusoidal

Line Regulation: ± 5% at at max. power for a +/- 10% line voltage

Duty Cycle: Intermittent: 30 sec. on, 30 sec. off

Audio: Adjustable from >45 dba to >65 dba at 1 meter

Display Settings:

Low Output Terminal

• 0-10 range: 0.1 watt increments
• 10-20 range: 1 watt increments

Bipolar & High Output Terminals

• 0-35 range: 1 watt increments

60 Hz Leakage: 50 microamps max. third wire of line cord open

Mains Power Cord: 18 AWG/3 105o C 300V / IEC-320-C13 connector, 10 ft. (3m)

Environmental

Operating Temperature Range: +10 degrees to +40 degrees C

Relative Humidity: 10% to 95% non-condensing

Storage Restrictions: -40 degrees to +70 degrees C, 95% humidity N.C.

Approvals:

• UL 544, Medical and Dental Equipment, E68077
• EN 60601-1 / IEC 60601-1

Protection: BF Defibrillator, Class 1